A look at our 2012 ReSpace blitz build of the Light Wall Pavilion. Auction ends on June 11th at 8:00 pm! Visit http://habitatonlineauction.com/ for bidding information.
Click here to visit our home website page to view events and headlines
From our CEO Kevin Campbell:
February 8, 2013
I attended Habitat for Humanity’s annual legislative advocacy conference in Washington, D.C. earlier this week. Habitat has long held that our building houses alone will not get us anywhere close to eliminating substandard housing from the world, but that our building of homes plus a strong advocacy voice will be what it takes.
In Proverbs 31:8-9 we hear our call to advocacy:
“Speak up for those who cannot speak for themselves,
for the rights of all who are destitute.
Speak up and judge fairly;
defend the rights of the poor and needy.”
Habitat has a strong brand and we have access to speak to those in power on behalf of those we serve and are yet to serve who have a need for better housing.
There is a definite budget-balancing rhetoric in Washington these days as there should be. Even so, we took our message to Capitol Hill that the small amount of federal funding that Habitat receives is vitally important to help us to continue to reach more families in our communities with a housing need. I was able to meet with staff from the offices of Sen. Kay Hagan and of Reps. Ellmer and Holding. All are familiar with Habitat’s work and we pray that effective federal programs such as HUD’s Self Help Homeownership Program (SHOP) that funds site acquisition and infrastructure development costs and the Corporation for National Service’s AmeriCorps and VISTA programs will be kept intact as Members of Congress seek ways to reduce federal spending. Click here to learn more about Habitat’s U.S. Domestic Policy priorities.
By speaking up for families in need who aren’t able to speak for themselves, we build louder and call attention to the great need for adequate housing across our country and world.
Instructions for Replacing a Light Fixture
- Start by turning off the power to the fixture’s circuit at the service panel.
- When you remove the fixture base on a wall or ceiling-mounted fixture, or the cover plate on a strip fluorescent fixture, test the wiring to verify that the power is indeed off. Probe each set of insulated wires with one lead of a neon tester and the metal box or grounding wire with the other. If the tester lights, the power is still on.
- Remove the screws or cap nuts that secure a globe or glass light shade.
- Remove the screws or cap nuts that secure the fixture, fixture body or canopy to the outlet box. Support the full weight of a heavy fixture during this step and the next. Get help for a heavy one, especially if you are working overhead from a ladder.
- With the wiring in the outlet box now accessible, repeat the power test described in step 2. When you’ve confirmed that there’s no power in the outlet box, remove the wire connectors that join the fixture wires to the house. If the fixture body is grounded, remove the screw or nut that secures the grounding (green) wire.
- You must secure fixtures that weigh over 50 lbs. (23 kg) independently of the electrical box. If you have access from above, install wood bridging between the joists above the box. Then screw the box into the bridging from below. If you don’t have access to install a support from above, purchase retrofit mounting hardware for a ceiling fan and install it according to the manufacturer’s instructions.
- Compare new mounting-hole requirements with the existing provisions at the outlet box. If necessary, purchase a new mounting strap or a universal mounting plate, which will accommodate virtually any fixture.
- Connect the new fixture to the same wires that connected the old fixture, and mount the fixture to the box with screws or cap nuts as required. Create a loop in the wires with long-nose pliers, then wrap them clockwise under a terminal screw. Or use electrician’s pliers to twist the wires from a prewired fixture together with the house wires, then secure them with wire nuts. Cut off excess with wire cutters.
- Mount the fixture with to the junction box and secure with external screws or nuts that came with your light fixture.
Instructions for Replacing a Door Knob
Remove the Old Doorknob
- Unscrew the screws that are holding the doorknob in place.
- Pull on both knobs at the same time and they will come apart. Remove the old doorknob and set it aside.
- If you want to replace the strike plate, remove it by unscrewing the screws and pulling it from the door frame.
Install the New Doorknob
- Place the new latch into its place and screw into place.
- Put both doorknobs and trims in place on either side of the door. Make sure that they fit together on the inside of the door and that the holes for the long screws line up.
- Insert the long screws into the doorknob on both sides. Tighten the screws alternately, first on one side, and then the other.
- Make sure the screws are screwed in tightly. If the doorknob rattles, the screws must be tightened.
- Place the new strike plate onto the door frame and screw into place.